LM2754SQ/NOPB

Texas Instruments
926-LM2754SQ/NOPB
LM2754SQ/NOPB

メーカ:

詳細:
LED照明ドライバIC 800mA switched capac itor flash LED driv

ECADモデル:
無料のライブラリローダーをダウンロードし、お使いのECADツール用にこのファイルを変換してください。ECADモデルの詳細について

在庫: 974

在庫:
974 すぐに出荷可能
工場リードタイム:
6 週間 表示されている時間を超える工場生産予定時間。
最小: 1   倍数: 1
ユニット価格:
¥-
合計 額:
¥-
EST関税:
パッケージング:
完全リール(1000の倍数で注文)

価格 (JPY)

数量 ユニット価格
合計 額
カットテープ/ MouseReel™
¥376.5 ¥377
¥278.7 ¥2,787
¥254.3 ¥6,358
¥228.2 ¥22,820
¥215.2 ¥53,800
¥207 ¥103,500
完全リール(1000の倍数で注文)
¥194 ¥194,000
¥185.8 ¥371,600
¥184.2 ¥921,000
† ¥750 MouseReel™の料金が追加され、ショッピングカートに加算されます。すべてのMouseReel™の注文は、キャンセルおよび返品できません。

製品属性 属性値 属性の選択
Texas Instruments
製品カテゴリー: LED照明ドライバIC
RoHS:  
4 Output
Boost
800 mA
WQFN-24
5.5 V
2.8 V
700 kHz to 1.3 MHz
LM2754
- 40 C
+ 85 C
Enable, True Shutdown
Reel
Cut Tape
MouseReel
ブランド: Texas Instruments
入力電圧: 2.8 V to 5.5 V
取り付け様式: SMD/SMT
チャンネル数: 4 Channel
出力タイプ: Constant Current, Constant Voltage
製品タイプ: LED Lighting Drivers
工場パックの数量: 1000
サブカテゴリ: Driver ICs
供給電流 - 最大: 8 mA
タイプ: Capacitive
単位重量: 38.600 mg
製品が見つかりました:
類似製品を表示するには、チェックボックスを1つ以上選択します
このカテゴリーの類似製品を表示するには、上記のチェックボックスを1つ以上選択してください。
選択した属性: 0

この機能はJavaScriptを有効にすることが必要です。

コンプライアンスコード
JPHTS:
854239099
CNHTS:
8542399000
CAHTS:
8542390000
USHTS:
8542390090
TARIC:
8542399000
MXHTS:
8542399901
ECCN:
EAR99
原産地分類
原産国:
マレーシア
組立原産国:
入手不可
拡散国:
入手不可
出荷時に原産国または地域が変更される場合があります。

IS32LT3175N/P Single-Channel Linear LED Drivers

ISSI IS32LT3175N/P Single-Channel Linear LED Drivers come with fade in/out and PWM dimming. The regulators serve as a stand-alone LED driver-configurable from 20mA to 150mA with external resistors, no microcontroller is necessary. A logic level “courtesy light” signal from the PWM pin can be interfaced to precisely drive the LED channel. The IS32LT3175P obtains a positive polarity PWM signal. In addition, the IS32LT3175N obtains a negative polarity PWM signal. The regulator integrates a 63-step fade-in and fades out the algorithm (Gamma correction). This causes the output LED current to increasingly rise up to the full source value after the EN pin is pulsed.