MPQ7221GRE-AEC1-Z

Monolithic Power Systems (MPS)
946-MPQ7221GRE-AEC1Z
MPQ7221GRE-AEC1-Z

メーカ:

詳細:
LED照明ドライバIC 16-Channel, 80mA/Ch, LED Driver

ECADモデル:
無料のライブラリローダーをダウンロードし、お使いのECADツール用にこのファイルを変換してください。ECADモデルの詳細について

在庫状況

在庫:
在庫なし
工場リードタイム:
64 週間 工場生産予定時間。
この製品はリードタイムが長いと報告されています。
最小: 5000   倍数: 5000
ユニット価格:
¥-
合計 額:
¥-
EST関税:
この製品は配送無料

価格 (JPY)

数量 ユニット価格
合計 額
完全リール(5000の倍数で注文)
¥409.1 ¥2,045,500

他のパッケージ

メーカ 部品番号:
梱包:
Reel, Cut Tape
在庫状況:
在庫
価格:
¥795
最低:
1

製品属性 属性値 属性の選択
Monolithic Power Systems (MPS)
製品カテゴリー: LED照明ドライバIC
RoHS:  
1 Output
Buck
80 mA
QFN-24
16 V
4.5 V
1.2 MHz
- 40 C
+ 125 C
AEC-Q100
Reel
ブランド: Monolithic Power Systems (MPS)
調光: PWM
取り付け様式: SMD/SMT
Pd - 電力損失: 1.79 W
製品タイプ: LED Lighting Drivers
工場パックの数量: 5000
サブカテゴリ: Driver ICs
製品が見つかりました:
類似製品を表示するには、チェックボックスを1つ以上選択します
このカテゴリーの類似製品を表示するには、上記のチェックボックスを1つ以上選択してください。
選択した属性: 0

コンプライアンスコード
TARIC:
8542399000
原産地分類
原産国:
入手不可
組立原産国:
入手不可
拡散国:
入手不可
出荷時に原産国または地域が変更される場合があります。

IS32LT3175N/P Single-Channel Linear LED Drivers

ISSI IS32LT3175N/P Single-Channel Linear LED Drivers come with fade in/out and PWM dimming. The regulators serve as a stand-alone LED driver-configurable from 20mA to 150mA with external resistors, no microcontroller is necessary. A logic level “courtesy light” signal from the PWM pin can be interfaced to precisely drive the LED channel. The IS32LT3175P obtains a positive polarity PWM signal. In addition, the IS32LT3175N obtains a negative polarity PWM signal. The regulator integrates a 63-step fade-in and fades out the algorithm (Gamma correction). This causes the output LED current to increasingly rise up to the full source value after the EN pin is pulsed.

MPQ7221 16-Channel LED Drivers

Monolithic Power Systems (MPS) MPQ7221 16-Channel LED Drivers operate across a wide 4.5V to 16V input voltage (VIN) range. These LED drivers integrate an I2C interface, where ten different I2C addresses are configurable via an external resistor. The MPQ7221 LED drivers apply 16 internal current sources in each LED string terminal. The LED current of each channel is set by an external current-setting resistor, with up to 80mA maximum current. These LED drivers employ separated Pulse Width Modulation (PWM) dimming and analog dimming to reach the LED channel. Each channel utilizes 12-bit resolution PWM dimming and 6-bit analog dimming.