LM3406MHX/NOPB

Texas Instruments
926-LM3406MHX/NOPB
LM3406MHX/NOPB

メーカ:

詳細:
LED照明ドライバIC 42-V 1.5-A constant current buck LED dri A 926-LM3406MH/NOPB

ECADモデル:
無料のライブラリローダーをダウンロードし、お使いのECADツール用にこのファイルを変換してください。ECADモデルの詳細について

在庫: 2,947

在庫:
2,947 すぐに出荷可能
工場リードタイム:
6 週間 表示されている時間を超える工場生産予定時間。
最小: 1   倍数: 1
ユニット価格:
¥-
合計 額:
¥-
EST関税:
パッケージング:
完全リール(2500の倍数で注文)

価格 (JPY)

数量 ユニット価格
合計 額
カットテープ/ MouseReel™
¥496 ¥496
¥372.8 ¥3,728
¥340.8 ¥8,520
¥307.2 ¥30,720
¥291.2 ¥72,800
¥281.6 ¥140,800
¥273.6 ¥273,600
完全リール(2500の倍数で注文)
¥262.4 ¥656,000
¥257.6 ¥1,288,000
† ¥750 MouseReel™の料金が追加され、ショッピングカートに加算されます。すべてのMouseReel™の注文は、キャンセルおよび返品できません。

他のパッケージ

メーカ 部品番号:
梱包:
Tube
在庫状況:
在庫
価格:
¥586
最低:
1

類似製品

Texas Instruments LM3406MH/NOPB
Texas Instruments
LED照明ドライバIC 1.5A CONSTANT CRNT B UCK REG A 926-LM340 A 926-LM3406MHX/NOPB

製品属性 属性値 属性の選択
Texas Instruments
製品カテゴリー: LED照明ドライバIC
RoHS:  
1 Output
Buck
1.5 A
HTSSOP-14
42 V
6 V
1 MHz
Adjustable
LM3406
- 40 C
+ 125 C
PWM Dimming, Constant Current
Reel
Cut Tape
MouseReel
ブランド: Texas Instruments
調光: 2-Wire, PWM
入力電圧: 6 V to 42 V
取り付け様式: SMD/SMT
チャンネル数: 1 Channel
出力タイプ: Adjustable
製品: Step Down
製品タイプ: LED Lighting Drivers
工場パックの数量: 2500
サブカテゴリ: Driver ICs
供給電流 - 最大: 1.2 mA
単位重量: 52.500 mg
製品が見つかりました:
類似製品を表示するには、チェックボックスを1つ以上選択します
このカテゴリーの類似製品を表示するには、上記のチェックボックスを1つ以上選択してください。
選択した属性: 0

この機能はJavaScriptを有効にすることが必要です。

JPHTS:
8542390990
CNHTS:
8542399000
CAHTS:
8542390000
USHTS:
8542390070
TARIC:
8542399000
MXHTS:
85423999
ECCN:
EAR99

IS32LT3175N/P Single-Channel Linear LED Drivers

ISSI IS32LT3175N/P Single-Channel Linear LED Drivers come with fade in/out and PWM dimming. The regulators serve as a stand-alone LED driver-configurable from 20mA to 150mA with external resistors, no microcontroller is necessary. A logic level “courtesy light” signal from the PWM pin can be interfaced to precisely drive the LED channel. The IS32LT3175P obtains a positive polarity PWM signal. In addition, the IS32LT3175N obtains a negative polarity PWM signal. The regulator integrates a 63-step fade-in and fades out the algorithm (Gamma correction). This causes the output LED current to increasingly rise up to the full source value after the EN pin is pulsed.