LM3559TLE/NOPB

Texas Instruments
926-LM3559TLE/NOPB
LM3559TLE/NOPB

メーカ:

詳細:
LED照明ドライバIC Synchronous boost fl ash driver with dua A 926-LM3559TLX/NOPB

ECADモデル:
無料のライブラリローダーをダウンロードし、お使いのECADツール用にこのファイルを変換してください。ECADモデルの詳細について

在庫: 267

在庫:
267 すぐに出荷可能
工場リードタイム:
6 週間 表示されている時間を超える工場生産予定時間。
最小: 1   倍数: 1
ユニット価格:
¥-
合計 額:
¥-
EST関税:
パッケージング:
完全リール(250の倍数で注文)

価格 (JPY)

数量 ユニット価格
合計 額
カットテープ/ MouseReel™
¥294.4 ¥294
¥217.6 ¥2,176
¥196.8 ¥4,920
¥176 ¥17,600
完全リール(250の倍数で注文)
¥144.3 ¥36,075
¥136.2 ¥68,100
¥131.2 ¥131,200
¥130.4 ¥326,000
† ¥750 MouseReel™の料金が追加され、ショッピングカートに加算されます。すべてのMouseReel™の注文は、キャンセルおよび返品できません。

他のパッケージ

メーカ 部品番号:
梱包:
Reel, Cut Tape, MouseReel
在庫状況:
在庫
価格:
¥253
最低:
1

類似製品

Texas Instruments LM3559TLX/NOPB
Texas Instruments
LED照明ドライバIC Synchronous boost fl ash driver with dua A 926-LM3559TLE/NOPB

製品属性 属性値 属性の選択
Texas Instruments
製品カテゴリー: LED照明ドライバIC
RoHS:  
2 Output
Boost
1.8 mA
DSBGA-16
5.5 V
2.5 V
2 MHz
5 V
LM3559
- 40 C
+ 85 C
I2C Control, OVP, PWM Control
Reel
Cut Tape
MouseReel
ブランド: Texas Instruments
入力電圧: 2.5 V to 5.5 V
取り付け様式: SMD/SMT
チャンネル数: 2 Channel
出力タイプ: Current Mode
製品タイプ: LED Lighting Drivers
工場パックの数量: 250
サブカテゴリ: Driver ICs
供給電流 - 最大: 750 uA
タイプ: Inductive
単位重量: 5 mg
製品が見つかりました:
類似製品を表示するには、チェックボックスを1つ以上選択します
このカテゴリーの類似製品を表示するには、上記のチェックボックスを1つ以上選択してください。
選択した属性: 0

この機能はJavaScriptを有効にすることが必要です。

JPHTS:
8542390990
CNHTS:
8542399000
CAHTS:
8542390000
USHTS:
8542390090
TARIC:
8542399000
MXHTS:
85423999
ECCN:
EAR99

IS32LT3175N/P Single-Channel Linear LED Drivers

ISSI IS32LT3175N/P Single-Channel Linear LED Drivers come with fade in/out and PWM dimming. The regulators serve as a stand-alone LED driver-configurable from 20mA to 150mA with external resistors, no microcontroller is necessary. A logic level “courtesy light” signal from the PWM pin can be interfaced to precisely drive the LED channel. The IS32LT3175P obtains a positive polarity PWM signal. In addition, the IS32LT3175N obtains a negative polarity PWM signal. The regulator integrates a 63-step fade-in and fades out the algorithm (Gamma correction). This causes the output LED current to increasingly rise up to the full source value after the EN pin is pulsed.