LP5860TRKPR

Texas Instruments
595-LP5860TRKPR
LP5860TRKPR

メーカ:

詳細:
LED照明ドライバIC 11 x 18 high-current LED matrix driver w

ECADモデル:
無料のライブラリローダーをダウンロードし、お使いのECADツール用にこのファイルを変換してください。ECADモデルの詳細について

在庫: 2,356

在庫:
2,356 すぐに出荷可能
工場リードタイム:
6 週間 表示されている時間を超える工場生産予定時間。
最小: 1   倍数: 1
ユニット価格:
¥-
合計 額:
¥-
EST関税:
パッケージング:
完全リール(3000の倍数で注文)

価格 (JPY)

数量 ユニット価格
合計 額
カットテープ/ MouseReel™
¥420.8 ¥421
¥312 ¥3,120
¥284.8 ¥7,120
¥256 ¥25,600
¥241.6 ¥60,400
¥232 ¥116,000
¥225.6 ¥225,600
完全リール(3000の倍数で注文)
¥217.6 ¥652,800
¥212.8 ¥1,276,800
† ¥750 MouseReel™の料金が追加され、ショッピングカートに加算されます。すべてのMouseReel™の注文は、キャンセルおよび返品できません。

製品属性 属性値 属性の選択
Texas Instruments
製品カテゴリー: LED照明ドライバIC
RoHS:  
11 Output
1.8 A
VQFN-40
5.5 V
2.7 V
125 kHz
LP5860T
- 40 C
+ 85 C
Reel
Cut Tape
MouseReel
ブランド: Texas Instruments
調光: PWM
入力電圧: 2.7 V to 5.5 V
水分感度: Yes
取り付け様式: SMD/SMT
チャンネル数: 18 Channel
製品: LED Drivers
製品タイプ: LED Lighting Drivers
工場パックの数量: 3000
サブカテゴリ: Driver ICs
供給電流 - 最大: 6 mA
タイプ: LED High-Current Matrix Driver
製品が見つかりました:
類似製品を表示するには、チェックボックスを1つ以上選択します
このカテゴリーの類似製品を表示するには、上記のチェックボックスを1つ以上選択してください。
選択した属性: 0

この機能はJavaScriptを有効にすることが必要です。

CAHTS:
8542310000
USHTS:
8542310075
TARIC:
8542399000
ECCN:
EAR99

LP5860T LEDマトリックス・ドライバ

Texas Instruments LP5860T LEDマトリックスドライバは、高電流および高性能LEDマトリックスドライバです。このデバイスは、18定電流シンクとN(N =6/8/11)のスイッチングMOSFETを集積しており、N × 18LEDドットまたはN × 6RGB LEDをサポートします。LP5860Tは、最大11のLEDドット向けあるいは198個のRGB LED用に66つのMOSFETを集積しています。

IS32LT3175N/P Single-Channel Linear LED Drivers

ISSI IS32LT3175N/P Single-Channel Linear LED Drivers come with fade in/out and PWM dimming. The regulators serve as a stand-alone LED driver-configurable from 20mA to 150mA with external resistors, no microcontroller is necessary. A logic level “courtesy light” signal from the PWM pin can be interfaced to precisely drive the LED channel. The IS32LT3175P obtains a positive polarity PWM signal. In addition, the IS32LT3175N obtains a negative polarity PWM signal. The regulator integrates a 63-step fade-in and fades out the algorithm (Gamma correction). This causes the output LED current to increasingly rise up to the full source value after the EN pin is pulsed.